DESCRIPTION 

This Water Based Urethane Gloss is a high solids polyurethane. To begin with, it is a high-performance material. Due to this, it has excellent hardness, abrasion resistance, hot tire resistance, and chemical resistance. Additionally, it has a low VOC, as well as, a low odor system with multiple uses. This makes the water based urethane perfect for interior floors surfaces. The product is an excellent gloss urethane and has tenacious adhesion. Thus, it is applied to concrete surfaces easily. This urethane gloss is great for prep and seal projects, especially on stained concrete floors, or over partial flake epoxy systems. 

Advantages to CFS – Water Based Urethane Gloss: 

* Excellent abrasion and wear for longer use 

* Won’t yellow, UV resistance 

* Hot tire, chemical, and abrasion resistance 

* Low odor makes it great for indoor work 

DATA 

Container Size 1gallon 

Coverage Rates 350 square feet per gallon depending on concrete porosity, prep and application style.
VOCs <125 grams per liter 

Shelf Life Up to one year from manufacture date in its original, unopened container stored at room temperature. 

Appearance Wet - Clear
Appearance Dry - Clear and Very High Gloss 

DRY TIMES 

Pot Life - 45-60 Minutes 

Recoat or topcoats 6-12 Hours Light Foot Traffic 16-20 Hours 

Full Cure; Heavy Traffic 4-7 days 

based on 70 degrees, 50%RH. Temp. greatly effects curing. 

HOW TO USE 

SURFACE PREPARATION: The concrete surface must be deemed mechanically and structurally sound, thoroughly clean of debris and completely dry. Concrete must be
fully cured a minimum of 28 days. It is recommended to prepare the concrete surface by mechanical means such as shot blasting or diamond grinding with 30 grit or coarser diamonds to achieve a CSP-2 to CSP-3 profile. If using in a thin mil system such as acid stain, dye & seal, 2 or less clear coats, etc., an 80 grit diamond may be acceptable
to minimizes visual scratches in the finish, or the use of our 30 grit Concrete DNA Satellite pad. Vacuum concrete surface several times until dust thoroughly removed. If
applying over an existing, fully bonded coating that is outside its recommended recoat window, the surface should be sanded thoroughly with a 60-120 grit sanding screen
until the surface is completely dulled with scratches. Vacuum dust thoroughly, rinse with clean water and remove excess water with a wet/dry vacuum or floor scrubber.
Allow surface to dry completely prior to application of coating. Where applicable and with adequate ventilation, wipe the surface with acetone and a microfiber dust mop.
CAUTION: Acetone is extremely flammable! If using acetone follow all safety precautions, make sure no pilot lights, open flames, sources of static electricity, sparks or
extreme heat sources are present. Use recommended personal protection for acetone.
If mechanical floor grinding means of preparation are not suitable, it is recommended to prepare the surface with Super Blue and a 30 grit Concrete DNA Satellite pad. This
preparation method is only suitable for completely un-sealed, bare concrete surfaces. Apply Super Blue solution evenly on the surface using brushes, mops, brooms or an
approved floor scrubber and keep wet on the surface of 10 – 15 minutes. Remove excess acid
solution with a wet/dry vacuum of floor scrubber. Rinse surface thoroughly with
clean water and on the final rinse use EZ Clean to neutralize the surface pH. Inspect the floor to ensure the surface has reached an even and adequate surface profile. Repeat
the acid etch and neutralizing steps as necessary to achieve correct profile. Allow the floor to dry thoroughly for 24-72 hours prior to applying this product. ALWAYS use
proper personal protective equipment when working with muriatic acid.
Substrate, air and material temperatures must be no less than 50°F and not exceed 80°F. If applied outside these limits the coating may not achieve adequate film formation
and may have excessive air entrapment, bubbles, blushing or hazing. Please note that higher substrate, air and material temperatures as well as excessive humidity may speed
the cure rate of this product. Cooler temperatures and lower humidity may slow the cure rate of this product 

FOR PERSONAL PROTECTION USE GLOVES, GOGGLES, RESPIRATOR AND OTHER NECESSARY PPE. REFER TO SDS PRIOR TO USE